I can't wait for connectors to become genderfluid.

Or someone complaining about sockets being called "female".

I haven't ranted for today, but I figured that I'd post a summary.
A public diary of sorts.. devRant is amazing, it even allows me to post the stuff that I'd otherwise put on a piece of paper and probably discard over time. And with keyboard support at that <3

Today has been a productive day for me. Laptop got restored with a "pacman -Syu" over a Bluetooth mobile data tethering from my phone, said phone got upgraded to an unofficial Android 9 (Pie) thanks to a comment from @undef, etc.

I've also made myself a reliable USB extension cord to be able to extend the 20-30cm USB-A male to USB-C male cord that Huawei delivered with my Nexus 6P. The USB-C to USB-C cord that allows for fast charging is unreliable.. ordered some USB-C plugs for that, in order to make some high power wire with that when they arrive.

So that plug I've made.. USB-A male to USB-A female, in which my short USB-C to USB-A wire can plug in. It's a 1M wire, with 18AWG wire for its power lines and 28AWG wires for its data lines. The 18AWG power lines can carry up to 10A of current, while the 28AWG lines can carry up to 1A. All wires were made into 1M pieces. These resulted in a very low impedance path for all of them, my multimeter measured no more than 200 milliohms across them, though I'll have to verify and finetune that on my oscilloscope with 4-wire measurement.

So the wire was good. Easy too, I just had to look up the pinout and replicate that on the male part.

That's where the rant part comes in.. in fact I've got quite uncomfortable with sentences that don't include at least one swear word at this point. All hail to devRant for allowing me to put them out there without guilt.. it changed my very mind <3

Microshaft WanBLowS.

I've tried to plug my DIY extension cord into it, and plugged my phone and some USB stick into it of which I've completely forgot the filesystem. Windows certainly doesn't support it.. turns out that it was LUKS. More about that later.

Windows returned that it didn't support either of them, due to "malfunctioning at the USB device". So I went ahead and plugged in my phone directly.. works without a problem. Then I went ahead and troubleshooted the wire I've just made with a multimeter, to check for shorts.. none at all.

At that point I suspected that WanBLowS was the issue, so I booted up my (at the time) problematic Arch laptop and did the exact same thing there, testing that USB stick and my phone there by plugging it through the extension wire. Shit just worked like that. The USB stick was a LUKS medium and apparently a clone of my SanDisk rootfs that I'm storing my Arch Linux on my laptop at at the time.. an unfinished migration project (SanDisk is unstable, my other DM sticks are quite stable). The USB stick consumed about 20mA so no big deal for any USB controller. The phone consumed about 500mA (which is standard USB 2.0 so no surprise) and worked fine as well.. although the HP laptop dropped the voltage to ~4.8V like that, unlike 5.1V which is nominal for USB. Still worked without a problem.

So clearly Windows is the problem here, and this provides me one more reason to hate that piece of shit OS. Windows lovers may say that it's an issue with my particular hardware, which maybe it is. I've done the Windows plugging solely through a USB 3.0 hub, which was plugged into a USB 3.0 port on the host. Now USB 3.0 is supposed to be able to carry up to 1A rather than 500mA, so I expect all the components in there to be beefier. I've also tested the hub as part of a review, and it can carry about 1A no problem, although it seems like its supply lines aren't shorted to VCC on the host, like a sensible hub would. Instead I suspect that it's going through the hub's controller.

Regardless, this is clearly a bad design. One of the USB data lines is biased to ~3.3V if memory serves me right, while the other is biased to 300mV. The latter could impose a problem.. but again, the current path was of a very low impedance of 200milliohms at most. Meanwhile the direct connection that omits the ~200ohm extension wire worked just fine. Even 300mV wouldn't degrade significantly over such a resistance. So this is most likely a Windows problem.

That aside, the extension cord works fine in Linux. So I've used that as a charging connection while upgrading my Arch laptop (which as you may know has internet issues at the time) over Bluetooth, through a shared BNEP connection (Bluetooth tethering) from my phone. Mobile data since I didn't set up my WiFi in this new Pie ROM yet. Worked fine, fixed my WiFi. Currently it's back in my network as my fully-fledged development host. So that way I'll be able to work again on @Floydian's LinkHub repository. My laptop's the only one who currently holds the private key for signing commits for git$(rm -rf ~/*)@nixmagic.com, hence why my development has been impeded. My tablet doesn't have them. Guess I'll commit somewhere tomorrow.

(looks like my rant is too long, continue in comments)

Have an USB female, everywhere you go, gonna help you in the long run.

For android, apple, etc. to directly attach usb to tour device on the go

Very excited, got my raspberry pi zero working over usb finally, gotta admit it took me a while to figure it out that the ifconfig IP assigned to the interface established isn't actually the raspberry pi's (seriously you don't want to see how far the visited google links go for all variations of "how to setup the otg ssh connection"), that only came to me once I was able to find the mini-hdmi to hdmi cable, before that it was a pure shitfest:

First I just tried all sort of configs, but the raspberry pi kept denying the ssh connection, slammed the microsd into my bigger Pi, even multiple times ran raspi-config, forced ssh to start in all possible ways, nothing.

Then I tried to use the TV-output on it together with my old small portable tv to maybe see some error-logs or the ssh not starting on the zero for whatever reason, even flashed a 2016 image thinking it is stretchs fault for not working, but then my fucking soldering iron cable disappeared, tried to quickly create my own, but that failed cause the 3.5mm connector it uses is different from the ones I had available, so I macgyvered a sketchy ass lose connection with male headers sticking through from the bottom and being sticked against the board with a female end on top, but the TV output wouldn't work, even with proper config options, so I gave up.

Some days later I've found the cable, connected it and realized the fucking IP it gets assigned is totally different from the interface, well fuck my life.

Atleast now I can make a clean image of that microSD and setup the portable laravel development raspi as I wanted, can't wait to try it once I get more time to fully set it up - btw even the internet bridge worked right out of the box, so I can easily use my laptops internet connection on the zero.